#Two audio to usb converter how to#
#Two audio to usb converter manual#
#Two audio to usb converter software#

The instrument cable contains one wire and a shield. The most common TS cords are instrument cables. You cannot send a stereo signal through this audio cable. It is mono because you only have one channel through which to send the signal. This the audio cable or cord you use for your guitar, or for the left and right outputs of a synth or keyboard (assuming outputs are not balanced).

But not all jack leads are the same! HereвЂ™s a bit more detail on what you really need to know. An audio lead with a 1/4 inch plug is also known as a jack lead. The 1/4-inch (or 6.35mm) jack plug is the most common audio connector, and the most versatile. The 1/4-inch (6.35mm) Analog Plug Connector Then weвЂ™ll examine the inputs and outputs on some popular home recording studio gear to see how it all fits together. Sounds simple? Well, letвЂ™s start with an in-depth look at the most common audio cable types. So, how do you decide which is the right audio cable?ДЄs a general rule, you read what it says on your gear, or refer to the manual.

Get the audio connections right, and your audio recordings will sound good. Recording success has a lot to do with the audio cable types you choose.

#Two audio to usb converter software#

Your goal is to record a clean and loud enough signal from your microphone, guitar, keyboard, synth, or drum machine in your recording software or DAW. For example, the Focusrite 2i2 Audio Interface allows you to switch between line and instrument/mic level. The ideal thing is to buy an interface or mixer which accommodates both line and mic level. The problem you may experience, though, is a poor signal to noise ratio You may find the recording result is perfectly satisfactory. Start with the lowest output volume you can from the sending device, and gradually increase it so that you get a decent signal without distortion. So, when trying to record, your equipment is not in any real danger, provided you are very cautious with the levels of volume. However вЂњoverloadedвЂќ really means вЂњdistortionвЂќ rather than actual damage. This means that any interface or mixer with a microphone as an input may be overloaded when you hit it with a line-level signal. Mic levels are much lower than (typical) line-level signals. What Happens If You Send a Line Level Signal to a Mic Input? Choose this cable whenever you connect an instrument such as a guitar or bass guitar directly to your interface. You will also require a preamp to be raise the level to Line Level. Instrument Level is the most variable level signal which will travel through a TS connection.

#Two audio to usb converter manual#

Check the manual of your gear to be sure. Note that a lot of consumer audio equipment and semi-pro keyboards etc may have unbalanced line outputs so you will use a TS cable instead. an outboard preamp or processor) or instruments that output a balanced line level (synths, keyboards, drum machines etc). This is the standard type of signal and you should use TRS when connecting any non-instrument pieces of hardware to your interface (i.e.

Line Level is the highest signal level which travels through a TRS connection. Interfaces and mixers with built-in mic inputs usually have a built-in mic preamp too, so you shouldnвЂ™t need additional kit other than the cable. You use an XLR cable whenever you connect a microphone to your audio interface or mixer. The mic level signal requires a preamp to raise the mic level up to line level. Mic Level is the lowest signal level which travels through an XLR connection. You can refer to our post on digital audio to discover more about digital audio recording.ДЄudio Signals Explained вЂ“ Line, Mic and Instrument

#Two audio to usb converter how to#

In a home recording studio situation, you are mostly concerned with how to transmit the analog sound from your mics and instruments so that you can eventually capture the sound in your DAW or other recording app or software. WhatвЂ™s the difference between analog and digital audio cables? Analog cables work by transmitting information through a stream of electricity, and digital cables work by transmitting information through a long string of 1вЂ™s and 0вЂ™s (aka binary code).

Best Selling Stage and Studio Audio Cables.

The Inputs of a Typical Home Recording Studio Powered Monitor.

The Inputs and Outputs of a Typical Audio Interface.

TRRS (Tip-Ring-Ring-Sleeve) 3.5mm (1/8вЂі) Headphone and Mic Plug.

Stereo/TRS Cable (Tip-Ring-Sleeve) 3.5mm (1/8вЂі).

The 1/8-inch (3.5mm) Analog Plug Connector.

Stereo/TRS Cable (Tip-Ring-Sleeve) 6.35mm (1/4вЂі).

The 1/4-inch (6.35mm) Analog Plug Connector.

What Happens If You Send a Line Level Signal to a Mic Input?.

What is the difference between Mic, Line, and Instrument level?.

Video Tutorial: Audio Cables & Connectors Explained.